Single Time Lag Module (for Button Switches)


Single Time Lag Module (for Button Switches)

These sockets and switches have an expected standard delivery time of between 2 to 4 working days.



Show Prices Ex VAT

Prices

 *Free delivery on orders over £95.
Single Time Lag Module - Important: 1 module required per button | circuit
Single Time Lag Module - Important: 1 module required per button | circuit
£40.83 
£49.00



Notes


What is a Time Lag Module (for Button Switches)?

Staircase Time Lag Switches require a time lag module on the circuit to make them work. Staircase Time Lag Switches are actually momentary push to make switches similar to a Bell Push that you might use on your front door. We can combine Staircase Time Lag Switches with Toggle Light Switches on the same plate if required.

Staircase Time Lag Switches are designed for use in common areas where you might have multiple switching positions on a common lighting circuit where a temporary use of light is required. These are most commonly used to switch lights on in a stairwell and the beauty of this is that they will switch themselves off after a pre-set time.

Previously Staircase Time Lag switches have only been available as air-operated push buttons and as they were only available in a plain white finish with an unsightly large white button plunger they were found to be unsuitable for many properties where something more stylish was a requirement.

You will require only one Staircase Time Lag Module per circuit and you can use as many Staircase Time Lag Switches as you like. The modules are usually located remotely and out of sight. They have a fully adjustable time delay setting from 30 seconds up to 10 minutes that is pre-set on installation – this then enables the users to press the push button Staircase Time Lag Switch briefly to switch ON the lights then after the pre-set time has elapsed the lights will switch OFF automatically.

With Staircase Time Lag Switches you cannot use standard on/off switches on the same circuit and all other switch positions will also need to be  Staircase Time Lag Switches.

Never use a Staircase Time Lag Module that is not rated higher than the total load applied to it – the maximum loads are 2300w (240v) or 1500w (12v) or 1000w (Fluorescent) or 460w (LED).

We recommend 25mm or 35mm deep wall boxes for mounting our button dimmer switches. If you require any advice or assistance please call our sales team on 01926 289289.



Customer reviews for the Single Time Lag Module (for Button Switches)


No reviews yet - Be the first to Rate the Single Time Lag Module (for Button Switches)

Other reviews for Sockets & Switches Sockets & Switches are

Average customer rating: Product Rating 21 out of 55 stars  21  reviews

Product Rating 5 out of 5      Put Together Own Switches
07 April 2021 by , Exeter - Verified Customer

Made our own switches to match what we had in the kitchen. Named switched really useful for knowing what it switches.


Product Rating 5 out of 5      Updated Current Unit
04 April 2021 by , Diss - Verified Customer

Updated current unit


Product Rating 5 out of 5      Quality
04 April 2021 by , Edgbaston - Verified Customer

Excellent bit of kit, easy to install, looks far more expensive than it is.


Product Rating 5 out of 5      Proper Boxes
03 April 2021 by , Reading - Verified Customer

Bought these boxes as solid metal not metal over plastic. More expensive but really good quality.


Product Rating 5 out of 5      Brilliant
03 April 2021 by , Cirencester - Verified Customer

The switch fits in, works well and matches the other switches in the house.


Product Rating 5 out of 5      A Good Find
27 March 2021 by , Ipswich - Verified Customer

These are a good find for a customer that wanted non plastic wall boxes. Bookmarked for future projects.


Product Rating 5 out of 5      Awkward Switch Fixed!
26 March 2021 by , London - Verified Customer

We needed a switch to fit inbetween two door frames at the top of the stairs but the design of the house only left a small gap to fit it into. After searching, this switch fits perfectly and we can have our three switch lighting for the stairs and landing.


Product Rating 5 out of 5      Ideal Replacement
25 March 2021 by , Reading - Verified Customer

Replaced our old bathroom light switch with an almost matching one. Surprised they are still made now.


Product Rating 5 out of 5      Solid!
21 March 2021 by , Winchester - Verified Customer

Real solid metal wall boxes. Even better comes in different colours. Used twice for customers already.


Product Rating 5 out of 5      Fits Perfectly
21 March 2021 by , Lancashire - Verified Customer

The switch fits perfectly in the narrow space between 2 doors. Great buy.


Product Rating 5 out of 5      Glad I Found These
20 March 2021 by , Cardiff - Verified Customer

Had some older speaker posts that were looking tatty and starting to cause interference so glad found these to replace them


Product Rating 5 out of 5      Seems Obvious Now
14 December 2020 by , London - Verified Customer

After looking everywhere for a thinner switch finally found these. Great idea and fits beautifully. If only I would have known would have saved a lot of time.


Product Rating 5 out of 5      Dimmer Knobs Metal
28 May 2020 by , Manchester - Verified Customer

Was plesently surprised these knobs are metal not plastic so bargain at the price and easy to fit.


Product Rating 5 out of 5      Useful Find
28 May 2020 by , Birmingham - Verified Customer

So glad to find these dimmer buttons. Saved me having to buy a whole new unit. Extensive choice of colours too.


Product Rating 5 out of 5      Unique Hard To Find Item
03 May 2020 by , Powys - Verified Customer

So happy to find a solid wall box to match my socket. Didnt realise that it would be like trying to find the Holy Grail.


Product Rating 5 out of 5      Brilliant
25 June 2019 by , London - Verified Customer

Very happy with these hard to find surface socket boxes. Spot on!


Product Rating 5 out of 5      Perfect Hard To Find Item
10 June 2019 by , London - Verified Customer

I searched everywhere for surface mount boxes in Black and in Bronze. After weeks of searching I found these and they are perfect. Very well made too.


Product Rating 5 out of 5      Great Idea
14 May 2019 by , Bristol - Verified Customer

These set my job apart and my client was over the moon with these boxes. Well made too.


Product Rating 5 out of 5      Brilliant
13 March 2019 by , London - Verified Customer

Hard to find - these are very well made and I was able to drill them easily. Perfect item for mounting switches on the bare brick wall.


Product Rating 5 out of 5      Problem Solved
23 February 2019 by , Royal Lytham - Verified Customer

I have a listed building so I cant mess around burying cables and disturbing the walls. These very well made surface boxes matched my socket fronts perfectly and it was problem solved. I had to wait two weeks for delivery though but I understand that these are made to order. Well worth the wait and the money.


Product Rating 5 out of 5      Great Product & High Quality
25 January 2019 by , Harlech - Verified Customer

Im amazed to find these as I was searching for months. Extreme quality these are very solid. 10/10




Review The Single Time Lag Module (for Button Switches)

Please enter your review for the Single Time Lag Module (for Button Switches) here

 Rating:
Please rate the product - 5 excellent to 1 not so good.
 

Review Title:

Your review

 

Name:

Email:

Location:


(Please enter village, town, area or city only - no postcodes please)
Thank you.   



Please click here to see the range of Sockets & Switches Time Lag Module (for Button Switches)s

© 2021 Copyright Sockets And Switches
Sockets & Switches, Unit 4 Althorpe Enterprise Hub, Althorpe Street, Leamington Spa, Warwickshire, CV31 2GB  |  enquiries@socketsandswitches.com